Buy on Etsy → — ships from our Etsy shop with Etsy buyer protection and reviews.
Front or Rear‑Center | 2006–2013 P1 Platform | OEM Ref. 31256444 / 31256445
Sagging headliners are one of the most common issues on the Volvo C70 convertible — especially as the factory backing becomes brittle with age. These replacement clips restore proper tension and support without paying retail kit prices for parts you already have.
Printed in durable PETG (black) to match the factory headliner backing and designed as a simple push‑fit solution.
🔧 Features
🧩 Direct‑fit replacement for C70 convertible headliner clips
🚗 Fitment: Volvo C70 (2006–2013) — P1 platform
📦 Pack of 4 — choose Front or Rear Panel
Full repair typically uses 16 clips total (8 front smaller and 8 rear larger)
🔥 PETG Black — strong, heat‑resistant, interior‑safe
🔩 OEM Reference:
31256444 (Center + Front)
31256445 (Center + Rear)
These are aftermarket‑printed equivalents; reuse your factory felt washers or source separately. Includes clips for the mounts. Note: due to their small, detailed geometry, these are not as strong as the OEM clips — best suited as a budget/temporary fix or for low-stress use. So I am throwing these clips in for free. Use at your own discretion.
🛠️ Simple push‑fit install — no special tools required
⚠️ Note: Install carefully — headliner backing can be brittle on cars this age
Made to order in Chattanooga, TN
⚡ Quick Install Instructions (with Icons)
(Instructions based on standard C70 headliner clip replacement.)
1️⃣ Remove the sagging headliner section
Gently pull down the loose portion to expose the failed clips.
2️⃣ 🧹 Clear out broken OEM clips
Remove any cracked or brittle factory clips from the mounting points.
3️⃣ 🔩 Insert new PETG clips
Press each clip firmly into the headliner backing until fully seated.
These are push‑fit replacements — no tools needed although glue is recommended for stronger adhesion.
4️⃣ 🎯 Align the headliner with the roof frame
Line up each clip with its corresponding hole.
5️⃣ 🤜 Press the headliner back into place
Push along the length of the panel until all clips lock in securely.
6️⃣ ✔️ Final check
Ensure the headliner sits flush and no sections sag.
📌 Notes
Order Front or Rear panel depending on which section is sagging.
For a complete refresh, order both listings (16 clips total).
PETG provides improved durability over brittle OEM plastic.
Disclaimer: This is not an OEM (Original Equipment Manufacturer) part. It is a 3D-printed reproduction designed to replicate the fit and function of the original component. As a reproduction, it may have some differences from the OEM part in feel, sound, fit, or overall finish. Minor adjustments may be needed during installation, and normal care should be taken when installing or removing the part, as it may not have the exact same strength or flexibility as the factory original. By purchasing, you acknowledge this is a reproduction part and not a genuine manufacturer component.
Buy on Etsy → — ships from our Etsy shop with Etsy buyer protection and reviews.
Front or Rear‑Center | 2006–2013 P1 Platform | OEM Ref. 31256444 / 31256445
Sagging headliners are one of the most common issues on the Volvo C70 convertible — especially as the factory backing becomes brittle with age. These replacement clips restore proper tension and support without paying retail kit prices for parts you already have.
Printed in durable PETG (black) to match the factory headliner backing and designed as a simple push‑fit solution.
🔧 Features
🧩 Direct‑fit replacement for C70 convertible headliner clips
🚗 Fitment: Volvo C70 (2006–2013) — P1 platform
📦 Pack of 4 — choose Front or Rear Panel
Full repair typically uses 16 clips total (8 front smaller and 8 rear larger)
🔥 PETG Black — strong, heat‑resistant, interior‑safe
🔩 OEM Reference:
31256444 (Center + Front)
31256445 (Center + Rear)
These are aftermarket‑printed equivalents; reuse your factory felt washers or source separately. Includes clips for the mounts. Note: due to their small, detailed geometry, these are not as strong as the OEM clips — best suited as a budget/temporary fix or for low-stress use. So I am throwing these clips in for free. Use at your own discretion.
🛠️ Simple push‑fit install — no special tools required
⚠️ Note: Install carefully — headliner backing can be brittle on cars this age
Made to order in Chattanooga, TN
⚡ Quick Install Instructions (with Icons)
(Instructions based on standard C70 headliner clip replacement.)
1️⃣ Remove the sagging headliner section
Gently pull down the loose portion to expose the failed clips.
2️⃣ 🧹 Clear out broken OEM clips
Remove any cracked or brittle factory clips from the mounting points.
3️⃣ 🔩 Insert new PETG clips
Press each clip firmly into the headliner backing until fully seated.
These are push‑fit replacements — no tools needed although glue is recommended for stronger adhesion.
4️⃣ 🎯 Align the headliner with the roof frame
Line up each clip with its corresponding hole.
5️⃣ 🤜 Press the headliner back into place
Push along the length of the panel until all clips lock in securely.
6️⃣ ✔️ Final check
Ensure the headliner sits flush and no sections sag.
📌 Notes
Order Front or Rear panel depending on which section is sagging.
For a complete refresh, order both listings (16 clips total).
PETG provides improved durability over brittle OEM plastic.
Disclaimer: This is not an OEM (Original Equipment Manufacturer) part. It is a 3D-printed reproduction designed to replicate the fit and function of the original component. As a reproduction, it may have some differences from the OEM part in feel, sound, fit, or overall finish. Minor adjustments may be needed during installation, and normal care should be taken when installing or removing the part, as it may not have the exact same strength or flexibility as the factory original. By purchasing, you acknowledge this is a reproduction part and not a genuine manufacturer component.
Image 1 of 6
Image 2 of 6
Image 3 of 6
Image 4 of 6
Image 5 of 6
Image 6 of 6