Buy on Etsy → — ships from our Etsy shop with Etsy buyer protection and reviews.
A worn or broken window regulator clip is one of the most common causes of a window that drops, binds, or refuses to stay up on Volvo P2‑platform cars. When this small plastic clip fails, the actuator loses its guide point — causing the glass to tilt, jam, or fall into the door.
This replacement clip restores proper alignment and smooth window travel without needing a full regulator swap.
🔧 Features
🧩 Direct‑fit replacement for the P2 window actuator clip
🚗 Fitment: Volvo S60 / V70 (2000–2007) — P2 platform
📦 Sold individually — most repairs only require replacing the one broken clip
🔥 Material: 3D‑printed PETG Black for strength + heat resistance
🛠️ Quick install — no regulator removal required
Made to order in Chattanooga, TN
⚡ Quick Install Instructions
(These instructions are based on standard P2 regulator clip replacement steps.)
1️⃣ Remove the door card
Pop the trim panel off and disconnect the switch panel.
2️⃣ 🔍 Locate the broken clip
You’ll see the actuator arm with the failed plastic guide.
3️⃣ 🧹 Clear debris
Remove any broken OEM clip fragments from the track.
4️⃣ 🔩 Snap in the new PETG clip
Press the replacement clip onto the actuator arm until fully seated.
5️⃣ 🎯 Re‑engage the window glass
Align the glass with the clip channel and slide it into position.
6️⃣ ✔️ Test operation
Cycle the window up and down to confirm smooth travel.
7️⃣ 🔧 Reinstall the door card
Reconnect wiring, press the panel back into place, and secure screws.
📌 Notes
Sold as a single clip — check your regulator to confirm how many are broken before ordering.
PETG provides improved durability over the brittle OEM plastic.
Disclaimer: This is not an OEM (Original Equipment Manufacturer) part. It is a 3D-printed reproduction designed to replicate the fit and function of the original component. As a reproduction, it may have some differences from the OEM part in feel, sound, fit, or overall finish. Minor adjustments may be needed during installation, and normal care should be taken when installing or removing the part, as it may not have the exact same strength or flexibility as the factory original. By purchasing, you acknowledge this is a reproduction part and not a genuine manufacturer component.
Buy on Etsy → — ships from our Etsy shop with Etsy buyer protection and reviews.
A worn or broken window regulator clip is one of the most common causes of a window that drops, binds, or refuses to stay up on Volvo P2‑platform cars. When this small plastic clip fails, the actuator loses its guide point — causing the glass to tilt, jam, or fall into the door.
This replacement clip restores proper alignment and smooth window travel without needing a full regulator swap.
🔧 Features
🧩 Direct‑fit replacement for the P2 window actuator clip
🚗 Fitment: Volvo S60 / V70 (2000–2007) — P2 platform
📦 Sold individually — most repairs only require replacing the one broken clip
🔥 Material: 3D‑printed PETG Black for strength + heat resistance
🛠️ Quick install — no regulator removal required
Made to order in Chattanooga, TN
⚡ Quick Install Instructions
(These instructions are based on standard P2 regulator clip replacement steps.)
1️⃣ Remove the door card
Pop the trim panel off and disconnect the switch panel.
2️⃣ 🔍 Locate the broken clip
You’ll see the actuator arm with the failed plastic guide.
3️⃣ 🧹 Clear debris
Remove any broken OEM clip fragments from the track.
4️⃣ 🔩 Snap in the new PETG clip
Press the replacement clip onto the actuator arm until fully seated.
5️⃣ 🎯 Re‑engage the window glass
Align the glass with the clip channel and slide it into position.
6️⃣ ✔️ Test operation
Cycle the window up and down to confirm smooth travel.
7️⃣ 🔧 Reinstall the door card
Reconnect wiring, press the panel back into place, and secure screws.
📌 Notes
Sold as a single clip — check your regulator to confirm how many are broken before ordering.
PETG provides improved durability over the brittle OEM plastic.
Disclaimer: This is not an OEM (Original Equipment Manufacturer) part. It is a 3D-printed reproduction designed to replicate the fit and function of the original component. As a reproduction, it may have some differences from the OEM part in feel, sound, fit, or overall finish. Minor adjustments may be needed during installation, and normal care should be taken when installing or removing the part, as it may not have the exact same strength or flexibility as the factory original. By purchasing, you acknowledge this is a reproduction part and not a genuine manufacturer component.
Image 1 of 5
Image 2 of 5
Image 3 of 5
Image 4 of 5
Image 5 of 5